Contact Us • Tel: +1 510 653 7555 • Fax: +1 510 653 9754
Showroom Location: 1145 Park Avenue • Emeryville, California 94608 USA

1985 Porsche 962C

$100,000+ in Pre-season Preparation. Works Completed by 962 Experts, Retro Sport. 1987 and ’89 Le Mans History. Race Ready and Fully Sorted

Inquire about this car

sold

VIN 962C-110
Exterior Color Almeras Livery
Interior Color Black Seat
Engine 2.8 Litre Twin Turbocharged Flat-6
Transmission 5-Speed Transaxle
Status Sold
Stock FJ711

Comments

1985 Porsche 962C
s/n 962-110
Almeras Brothers Period Livery

Serial number 962C-110 was originally sold to Kremer Porsche in March of 1985, and run in the 1985 season, where it suffered a racing accident at the 1000kms of Mosport in August of that year. In 1987, 962C-110 was subsequently rebuilt utilizing a Thompson tub, to 1987 specifications. It was run by Kremer in 1987 and 1988. It was then sold to the Almeras brothers (incidentally the first Frenchmen to own and race a 962C) for the 1989 season, during which they campaigned the car extensively. The car’s exploits were documented in a book of theirs, and the car retains its Almeras livery today. Most recently the car competed with nearly 30 other GTP/Group C cars at the Monterey Historic Automobile Races- undoubtedly the most significant vintage race weekend in North America. Further accolades were accumulated at the 2009 Carmel-By-The-Sea Concours where the car won multiple awards. 962-110’s competition history is as follows:
1987
Jarama – 4th
Jerez – 2nd
Hockenheim – 2nd
Silverstone – DNF
Le Mans – DNF (Kremer/Kenwood livery)
Nurburgring – 14th
Eifelrennen
Spa – DNF
Fuji – DNF

1988
Silverstone – DNF (Kremer)
Interseries SAT Livery
Flugplatzrennen
Sold to Almeras brothers

1989
Dijon – 19th
Jarama – 12th
Brands Hatch – 10th
Nurburgring – 14th
Spa – 21st
Le Mans – DNF
Trofeo Hermanos Rodriguez Mexico — 15th

2009
Pre-Historic Automobile Races, Laguna Seca
Monterey Historic Automobile Races, Laguna Seca

Critically, the car was raced at Le Mans in period, making the car eligible for the Le Mans retrospective. The Almeras brothers rebuilt the engine and generally freshened the car just prior to selling it to an American collector who kept the car (alongside his Ferrari GTO and Maserati 200S) until 2003. The car ran and retains air/water intercoolers, 2.8 litre engine, KKK turbos, and Bosh 1.2 Motronic. The car was treated to a service in December of 2002 that included bodywork, cooling system, fuel system, clutch master cylinder, minor brake service, and miscellaneous hoses and clamps.

During 2009 s/n 110 saw a no-expense spared, massive, pre-season preparation by Porsche 962 expert restoration and service shop Retrosport Racing to ready the car for any European Class C or USA IMSA GTP events:

TUB AND CABIN

Tub and Cabin Works Completed
• Remove bodywork and aero-package undertray, inspect and repair as needed.
• Remove suspension, engine, transaxle, all system components, coolers/radiators, hoses, fire system, seats, belts, fuel cell, etc., to nearly a bare tub, everything except the wiring, dash panel, and windscreen.
• Remove and send out the fire system for testing.
• Remove and replace high pressure fuel pumps with new correct Bosch 979 pumps.
• Remove and replace tested fuel cell/system and new hoses.
• Remove and replace seat belts with new Sabelt Seat Harness.
• Replace missing seat titanium bolts and hardware.
• Crack test all three pedals and linkages.
• Replace modified fuel pedal with an original pedal, relocate pivot points and bracket in tub.
• Relocate clutch and brake pedal pivot points and bracket in tub.
• Service fuel pedal cable and ends.
• Inspect and test all electrical dash components.
• Repair passengers seat and pump/electrical box cover.
• Replace battery with new Optima and cables.
• Relocate boost knob back to hole in dash (original location).
• Install new old stock 962 MOMO steering wheel.
• Clean tub and inspect all structure and pick-up points.
• Install new door seals.

Outside Services
• Machine new seat sliders and hardware (titanium)
• Fire system inspection (Halon unit weight and components).
• Crack testing.
• Electrical instrument testing/service.
• Passenger seat fiberglass repairs.
• Machine MOMO wheel for Porsche hub.

New Parts
• Original MOMO Steering Wheel.
• High Pressure Fuel Pumps.
• Fuel Cell Fill, gaskets, bolts.
• Original Fuel Pedal.
• Yellow-top Optima Battery.
• Door Seals.
• Sabelt seat Harness.
• Titanium Seat Hardware.

ENGINE
Engine Works Completed
• Gather baseline information on running engine before rebuild, leakdown tests, compression tests, Borescope cylinders, temp checks engine/headers/turbos/radiators/ oil/etc., pressures, fuel mixture, response, computer inputs, etc.
• Clean engine/gearbox/suspension/tub, before removal from car.
• Remove engine and attaching components, tag and store.
• Clean/detail exterior of engine before starting work on engine.
• Verify valve timing and piston to valve clearances.
• Disassemble engine, remove; water pumps, camdeck 1-3 side/4-6 side, cams and buckets 1-3 side/4-6 side, heads/barrels 4-6 side, pistons,
• Initial cleaning of engine parts-hot tank, power wash, solvent wash.
• Verify all engine components to ensure they are within factory wear limits.
• Send parts to the machine shop as required, final check and measure after return from shop.
• Detailed inspection of engine/components while disassembled.
• Pressure test heads, inspect/replace valves/springs/etc.
• Locate and purchase new old stock water head with correct compression/size/specs to replace #5 which had a leak near the valve seat under pressure test.
• Machine new head for proper valve set-up.
• Assemble heads/lap valves/measure heights/set-up valve springs/assemble heads.
• Install pistons/rings/etc.
• Install heads/cylinders/torque/etc.
• Set-up geardrive/install gearbox.
• Assemble camdecks, install cams, buckets, adjust valves, set cam timing on 1-3 side and 4-6 side of engine.
• Rebuild water pumps, machine impellers, add updated seals, install on motor.
• Clean and repair corroded original valve covers.
• Test electrics, alternator, ignition system, wiring, etc.
• Dress motor, covers, fan, alternator, fiberglass, etc.
• Clean, check, test, install; fuel system, injectors, sensors, plenums, harness, plugs, etc.
• Install ignition system.

Outside Services
• Machine works on new head, cut seats/grind valves, pumps and drives, misc., Norman Racing.

New Parts
• Complete 962 C gasket set.
• 962 piston ring set.
• Misc nuts, bolts, studs, etc.
• Spark plugs.
• Original 962-C NOS Air/water head.
• Silicone hose for water and turbo’s.
• Oils, Filters, Fluids, Greases, Sealants, etc.

GEARBOX/TRANSAXLE

Gearbox Works Completed
• Remove gearbox and associated components.
• Clean and detail box prior to start of works.
• Confirm gearbox and axle functions prior to disassembly, gear/drive specs, etc.
• Disassemble gearbox.
• Clean and inspect internals, ears, etc.
• Locate and purchase new parts as required, ring and pinion, one gear set, bearings, seals, etc.
• Replace crown wheel and pinion with new gear set 8/37, new bearings, etc.
• Set –up new ring and pinion, pinion depth, backlash, carrier bearing preload, etc.
• Final assembly of gearbox with selected gears.
• Clutch and flywheel inspection and clutch plate replaced with new old stock.
• Rebuild throw-out bearing and system.

New Parts
• Ring and Pinion gear set, 8/37.
• 962 trans gasket set for axle housing.
• 962 trans rear cover gasket set.
• 962 oil pump gaskets.
• 962 side cover o-rings.
• 962 carrier bearings.
• Ring and pinion bolts.
• Locking plate.
• 2nd gear set, 17/26.
• Proper 962 clutch plate.

MISCELLANEOUS ITEMS

Miscellaneous work items completed.
• Rebuild BBS wheels, new gasket rings/seals/bolts.
• New wing end plates made, carbon-fiber, not installed yet.
• Align bodyworks, set pins/clips/etc., rewire and test lights, etc.

SUSPENSION
• Complete removal of front and rear suspension, clean, tag, visually inspect, send out for NDE and X-Ray, repair/replace suspension pieces (1), paint and prep, install/set-up.
• Replace 3 incorrect material bolts with correct original spec titanium bolts, proper washers, and some minor rounded head nuts with new hardware for appearance.
• Rear Uprights, disassemble, crack test, inspect wheel bearings (replaced both sides with new (NOS) bearing 5-piece sets, and all seals), properly set-up new wheel bearings in uprights/hubs with Kluber and to Porsche 962 specs.
• Front wheel bearings replaced with new 5-piece sets and new original type seals, set-up pre-load, etc. with Kluber and to Porsche 962 specs.
• Original Porsche Calipers (8ea) remove and replace, clean, inspect and overhaul calipers/pistons w/new seals and parts as required, new Porterfield custom racing pads (16 ea), new hose fittings, hoses, bolts, set-up caliper alignment, floating tolerance, etc.
• Rotors, replace with new front and rear rotors, double heat treated, balanced, cross-drilled, sized, set run-out, etc., as original for car (design, size and vanes), inspect hats, dog rings, set clearance, new hat/rotor bolts and washers.
• Master cylinders, replace with proper new AP masters (3 ea), new hoses/fittings, titanium rods, bench bleed, set stroke/alignment/etc., rebuild balance system, re-set pedal pivot points in tub/bracket.
• Flush brake and clutch system after new installation of calipers/hoses/ftgs/cylinders, bleed system, test front/rear pressure balance and system functions/deflection.
• Dyno, Service/Rebuild, and Re-Dyno the original Bilstein shocks by Bilstein Racing USA.
Outside Services
• NDE and X-Ray suspension, QC Services, all X-Rays are in hand and available.
• Titanium brake push-rods, shorten, drill, thread for proper geometry.
• Some specialized hose fittings crimps/etc.
• Misc machine works on bearing set-up, rotor run-out, etc.
• Shocks rebuilt by Bilstein Racing USA.
New Parts
• Rear 5-piece Wheel Bearings and Seals
• Proper Kluber Wheel Bearing Grease, 2 liters
• Front 5-piece Wheel Bearings and Seals
• Front/Rear Brake and Clutch AP master cylinders
• Stainless Steel Brake lines and fittings
• Raychem heat shrink and heat shield materials
• New misc hardware, titanium, SS, clamps, etc.
• Racing brake pads, Porterfield R-4-1 (16 ea)
• Caliper seal kits (32 rings)
• Rotors, left and right directional, double-heat treated, cross-drilled, balanced, dog-ring matched, hat/rotor bolts.

FUEL SYSTEM

Fuel System Works Completed
• Remove and Replace high pressure fuel pumps with correct new Bosch “979” pumps.
• Rebuild/service high pressure fuel pump log manifold and o-ring seals/etc.
• Test and service low pressure fuel transfer pumps.
• Remove and Replace all Stainless Steel fuel lines and forged Stainless Steel fittings, and add Raychem shrink protection.
• Remove and test/service fuel cell (certify), replace bladder fill, re-tape fuel can, new gaskets and bolts on plates, new hoses on bladder plates, test/service low level warning sender/light.
• Send Injectors out for cleaning and flow testing to original specs.
• Change original old style Fuel Filters to Kinsler Filters.

Outside services
• Fuel Cell work/supply by AeroTech, Ca.
• Clean/test injectors by RC Engineering, Ca.

New Parts
• Forged Stainless fittings and SS hoses.
• Raychem heat shrink, flame guard.
• Kinsler fuel filters.

OIL SYSTEM

Oil System Works Completed
• Remove oil coolers and send out for cleaning, pressure testing, repair and surface coating.
• Re-plumb entire oiling system, new filters, new Wiggins O-rings throughout.

Outside Services
• Pacific Oil Cooler service for Ultrasonic and flow cleaning, testing, repair, surface coatings.

New Parts
• Wiggins O-Rings.
• Hose and fittings.
• Oil Filters.
• Oil Tank Breather Hose.

WATER HEAD COOLING SYSTEM

Cooling System Works Completed
• Remove Water Radiators and send out for cleaning, testing, repairs and coatings.
• Repair radiator support bracket, re-weld.
• Replace Silicone Hoses/clamps/etc.
• Weld in new Wiggins Ferrules on tubing.
• Replace all Wiggins O-Rings, service all fittings in system.
• Rebuild water pumps, machine new water pump impellers, new drive keys and shims.

Outside Services
• Pacific Oil Cooler Service, radiator service.
• Norman Racing machine water pump impellers.

New Parts
• Silicone hoses.
• Wiggins O-Rings.
• Water Pump Impellers, keys, shims, etc.

TURBO SYSTEM

Turbo Works Completed
• Remove and send out Turbos for overhaul and trim updates.
• Remove Wastegates and overhaul, grind valves, test, etc.
• New Silicone Hoses throughout.
• Remove and send out intercoolers for cleaning, testing, repairs and coatings.
• New gaskets/seals on exhaust side, align flanges/pipes.
• Service/inspect turbo oiling system.

Outside Services
• Turbo Overhaul, upgrades.
• Intercooler cleaning, testing, repair, coating service.
• Wastegate services.

New Parts
• Silicone hoses.
• Turbo and Wastegate Gaskets/seals/clamps.
• Turbo wheels/bearings/etc.
• Wastegate internal parts.

PRE-RACE CHECKOUT, TESTING AND SET-UP

Engine and Support Systems
• Test/Check/Calibrate all electrical systems and sensors during engine run.
• Test/Check all fuel system components for function, leaks, etc.
• Run-in engine and confirm all parameters per Porsche specs.
• Monitor all pressures and temperatures, boost, ECU signal codes, etc.
• Monitor Lambda and assess engine data acquisition information.
• Run engine/transaxle through all gears with wheels turning.

Chassis and Tub
• Set Caster, Camber, Toe, Corner Weight, Sway Bars, Ride Height, Bump, Steering Locks, etc. to Porsche specifications and current 962C race set-up experience.
• Full nut-and-bolt inspection of chassis/suspension, confirm torques, free-play and clearances, check all hose fittings and clamps, rim to suspension/hoses/lines, etc.
• Re-bleed brake system and clutch system, check for pedal bias bar bind and adjustment.
• Test actual brake pressures and bias between front/rear.
• Cycle throttle pedal/cable/arms/springs/throttle bodies for operation and clearance.
• Cycle all suspension unloaded and loaded, as well as steering lock-to-lock, etc.
• Adjust shifter and three-piece linkage, adjust reverse/1st ident.
• Set mirrors, seat position, seat belts, pedals, etc. to driver size requirements.
• Cycle/test air jack system, break valve, lines, mounts, etc.
• Confirm all lights, safety systems, car configuration, etc. for track technical inspection.


POST TEST TRACK DAY (THUNDERHILL, CA) FOLLOW-UP WORK ITEMS

• Clean chassis and perform a nut-and-bolt inspection of car.
• Check and fill all fluids, inspect for any drips/leaks/etc.
• Replace inaccurate boost gauge with new-old-stock (NOS) VDO original 962-C boost gauge and confirm operation.
• Check and replace tachometer wiring/lugs, confirm operation.
• Re-clock shifter away from front roll bar hoop for easier shifting into 4th /5th gears.
• Adjust shift linkage for smoother shifting, check/re-align rod arms and slides.
• Replace fuel pump seal washers at fuel log to stop small drip from pump #2.
• Reverse brake balance bar in pedal slide to get more rear bias and to allow for future adjustment for both front and rear bias per 962 spec book.
• Check and replace sensors that are not in spec or with damaged wiring.
• Confirm Bosch dash light codes are resolved after sensor replacement.
• Bleed brakes and check pad wear/rotor condition/etc.
• Adjust clutch for a little more pedal and more release, inspect clutch condition.
• Change out radiator water to distilled water with some inhibitor, bleed system.
• Pull spark plugs for inspection to confirm Lambda and injector operation.
• Visual inspection of engine and systems.
• Secure dash pad to prevent lifting at speed, Velcro/screws.
• Install temporary data logger for Monterey.
• Paint lower side panel-work where exhaust exits to proper Almeras Le Mans blue paint instead of white vinyl as found.


POST MONTEREY PRE-HISTORICS AND MONTEREY HISTORICS

• Prepare car to “race-ready” condition for the next significant historic race event.
• Perform complete nut-and-bolt chassis inspection after clean and wax.
• Replace troublesome non-standard aluminum shift linkage (too much flex) with original 962-C three-piece moly-steel tube shift linkage, replace joint bearings as needed, epoxy joints, align, properly clock shifter as required.
• Remove non-standard cockpit adjustable rear sway bar control lever and cable which interfered with drivers shift arm.
• Check throttle pedal pivot, lubricate throttle cable, adjust returns springs on throttle-bodies, check linkage arms.
• Check and fill all fluids as needed.
• Check brake system, bleed brakes, etc.
• Inspect spark plugs and visual engine/systems, review data acquisition files.
• Replace ducting on rear brake cooling pick-up with correct black duct material.
• Replace battery cover with the original 962-C from this car.

Although the car has recently won concours awards, it is presented in very good period racing cosmetic trim with all paint, livery and sticker items in excellent shape. The wheels display no oxidation, and the chassis, tub, and suspension components are in fine condition. The engine is also quite tidy, as is the interior, which is of course fully instrumented and well labeled.

Described by Derek Bell as “A beautifully efficient machine, easy to drive, with no bad habits”, Porsche’s 956 and 962 are absolutely legendary for their dominance in the international Endurance Sports Car racing scene throughout the eighties, and into the early nineties. Piloted by such legendary drivers as A.J. Foyt, Hans Stuck, Vern Schuppan, Jackie Ickx, Al Holbert, Hurley Haywood, and Jurgen Barth, among others, these cars secured many world championships and Le Mans victories for Porsche, including first place at Le Mans from 1982-1987, and again in 1994. The cars underwent Porsche’s fastidious and continuous development, seeing the inclusion of electronic fuel injection, and with the introduction of the 962 to replace the 956, improved safety from a longer wheelbase that placed the driver’s feet behind the front wheels, and numerous other improvements. The 962 represented the culmination of decades of Porsche’s racing experience, and even compared to the already devastating 956, the 962 was a more resolved and effective car still. Their production numbers were also higher, making them easier to supply parts for today.

This is an opportunity to acquire a 962 with excellent history and in excellent, race ready and fully sorted condition. Thanks to the tremendous success of these cars and increased interest in retrospective Group C events, there is an increasing number of vintage racing venues at which to use this car, ensuring that values will continue to increase as these cars become increasingly usable, and both the owner spectators will once again be able to experience this remarkable car doing what it was meant to do.
Track images courtesy of Dennis Gray.

 


Contact Information
Fantasy Junction +1 510 653 7555 Emeryville, California 94608 USA

The above vehicle information is complete and accurate to the best of our knowledge at the time it is posted to this website. Corrections or additional information is always appreciated. All advertised prices exclude government fees and taxes, any finance charges, any dealer document preparation charge, and any emission testing charge. Vehicles are subject to prior sale. All advertised to be true but not guaranteed. We assume no liability for errors or omissions.

Contact Information (required)

Fantasy Junction responds to email daily. If you do not hear from us within 48 hours, please check your email address for possible typos.